Restarted my truck and plugged in my iPhone and immediately was greeted with the prompt for CarPlay. There is not a lot of slack in the cables, so be careful when removing them.Ħ) I simply plugged the cables back into the new part but did not push it into the slot until I was sure it was going to work. Use a small jewelers screwdriver (smaller than shown in the YouTube video) and I was able to push in the restraining clip on one side and actually just pull out the part without any further effort. ĥ) Removing the old USB ports was easier than I thought. There is a newer part with a -E at the end, which supersedes the -B as stated here. Took less than 10 minutes.Ĥ) I was able to order the correct part from my local Ford dealer for around $60. NOTE: Make sure you use the recommended 8GB thumb drive so there is enough room during the upgrade in your vehicle for the compressed files to be extracted/installed.ģ) The actual software upgrade went way faster than I thought it would, mine was updated to Sync 3.0 (303024). Luckily on the Ford site they have screenshots showing how the files should appear and it was simply a matter of creating a folder and renaming the files. If you use the standard ZIP file utility in MacOS it will extract all of the necessary files, just not in the correct hierarchy. However when I did use it, it failed to extract the entire subfolder entitled SyncMyRide. It is a straight-forward process, but you need to pay attention to the details.ġ) DO follow the instructions on Ford’s website for downloading the Sync software updates, just enter your VIN number to get the correct update.Ģ) On the Mac, you can use Stuffit Expander. So a few updates for those who want to make this a reality. I bought my 2016 Ford F-150 XLT Platinum in 2019 and have always had general reliability and usability issues with the standard Sync interface, and always thought if it was only equipped with Apple CarPlay this vehicle would be absolutely perfect. Kevin, I can’t thank you enough for posting this. The system will let you know in the black bar at the top of the screen when it is updating. After redoing the USB stick setup, I plugged the drive into the USB ports again and the Sync System immediately began the update. When using the software recommended by the Ford provided instructions (Stuffit Expander – found on the Mac App Store) the files were structured correctly after being unzipped. After this failure I got on a chat with Ford and after a bit of conversation the issue that I ran into was that the Mac Archive Utility unpacks the updates from the Zip file incorrectly. I then began the process of going to and downloading the update to a USB drive, then forcing the update. When I came back a bit later and turned the truck on it read that it last checked for updates to Sync on the current date, and approximately an hour earlier. Nothing happened so I turned the truck off and went in to eat dinner. I read online about how to update, and that the system has the ability to automatically update when connected to WiFi, so when I returned home from work I connected the system to WiFi and waited for a bit. What I noticed was the software version in the video was something long the lines of Version 3.0, and when inspecting my software, I saw that the version was Version 1.0. I was frustrated, but continued to research. When following the basic video process, I ordered the part ( HC3Z-19A387-B) on Amazon, and immediately on receiving the part I attempted the quick install and was greeted with an error message saying something along the lines of “USB Hubs are not supported”. CarPlay and Android Auto were added in Version 2.2, and the current (as of ) build of Sync is Version 3. The software version that was installed was Version 1.0. The issue I ran into required two things, one – I would need that USB module, and two – the Sync 3 Version installed in the truck was very out of date. While that is a part of the process, it is not the complete process. The v ideo I found on YouTube went over the process and made it seem to be as simple as installing a different USB module into the center console of the truck. After doing some digging I found a video on YouTube that showed that I could get this functionality installed on my truck with a simple piece of hardware and while this started me down the right path, I wanted to share my process as I am sure many others have tried and failed due to some of the same issues. Recently I purchased a 2016 F150 and unfortunately, the 2016 lineup did not include Apple CarPlay at launch. I have used iPhone since its launch in 2007 and when Apple announced CarPlay I was extremely excited. CarPlay is an awesome functionality that I have wanted since it was launched.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |